• Home
  • Project Cars
    • 1972 Hemi Duster
    • 1966 Charger
    • 1968 Camaro SS
    • 1963 Impala
    • 1972 Cutlass
    • 1969 GTO Judge
    • 1969 Torino GT
  • Hot Rod Power Tour
    • Hot Rod Power Tour Instagram Feed!
    • Power Tour 2012
    • Power Tour 2013
    • Power Tour 2014
  • Forums

Must Read

  • Looking Back: A Hot Rod Power Tour Retrospective
  • The Dodge and the 2014 Power Tour
  • Hot Rod Power Tour 2014 Recap Pt. 3
  • Hot Rod Power Tour 2014 Recap Pt. 2
  • Hot Rod Power Tour 2014 Recap Pt. 1
  • Mr. Black and The Lincoln Reach an Important Milestone
  • Home
  • Project Cars
    • 1972 Hemi Duster
    • 1966 Charger
    • 1968 Camaro SS
    • 1963 Impala
    • 1972 Cutlass
    • 1969 GTO Judge
    • 1969 Torino GT
  • Hot Rod Power Tour
    • Hot Rod Power Tour Instagram Feed!
    • Power Tour 2012
    • Power Tour 2013
    • Power Tour 2014
  • Forums

Post #9 – Discretion is the Better Part of Valor

April 22, 2014  By Ralph Trimmer
2


Well…  Lots of things can change in a month’s time.  As machine work continued on my short block, it was discovered the honing on the .030 cylinder bore was not enough to eradicate the imperfections.  To some, this would not be an issue…  “I don’t mind – it’s just a tiny bit of rust pitting…  it won’t really affect the engine’s performance”  To those of us involved in PROJECT BEDLAM this discovery is an opportunity to step up and do the right thing.  The right thing is .010 more on the bore…  Result:  .040 bore.  After .040 bore and decking the block, the displacement is 468.  The resulting geometric configuration means new pistons.  New pistons means higher compression.  Larger displacement, new pistons, and 9.5:1 compression means a new cam.  Yes…  a new cam.  Though I just had a cam custom ground by BULLET, it will be sold to a dude building a slightly milder engine.  I have upgraded to a CROWER cam with a bit more duration…  This will, among other things, help alleviate static pressure in the cylinders, enhancing flow and realizing the potential of the build’s components.  A wee bit of rust set the cogs in motion to change the final product from an engine I hoped would make HP numbers approaching 400, to an engine which will likely make 450 HP, all the while maintaining its ability to hammer along on the highway.  One does not skimp whilst playing this game.

I have been notified my rear end will soon ship.  A recap on the rear end:  3.42 Limited Slip…  complete re-build, brakes included.  This set-up will prove to be a good choice at the drag strip.  The aforementioned engine changes result in my car requiring premium / 93 octane fuel.  The term, “egregious” was recently used by a pal, to describe my pending fuel bill for Power Tour…  I have made the executive decision to postpone installation of the bad-ass rear end until I have returned from the tour.  The result will be lower RPMs on the highway and a conservative break-in for my new engine…  My stock 2.73 / open carrier rear end will perform its swan song driven by beastly HP numbers…  I’ll need to behave.  Meaningful time slips will have to wait until later.  I may – or may not have time to upgrade  my front drum brakes to the Wilwood discs I previously mentioned.  450 HP and drum brakes at all four corners is suicide, if one intends to haul ass.  Somehow I am not disappointed…  I see this as another message from the Gods of speed, telling me to tread lightly for a while.  I’m cool with that.  Power Tour is about hooking up with pals, to enjoy a week of driving beasts, admiring each other’s handy work and sharing tales of the same…  We all have our tales of woe and things we should’ve and could’ve done.  Spending serious cash, knowing when to pull in the reins, cutting our losses, and making the June 7 Power Tour start…  All part of the journey.

I drove down to Danny’s this past Friday, to deliver more parts for the build and hang out for the afternoon.  We talked Oldsmobiles – his and mine – and what the future holds.  I headed back home, completing what was likely one of the last cruises for the tired, ol’ 350.  Very soon I will pull the current engine and transmission combo, to ready the engine bay for Danny’s handy work.  While tidying up the latter, I’ll drop the fuel tank.  forty two years of gum and rust have rendered the sending unit worthless.  The tank needs to go.  I have a new tank and sending unit, which I will install this week…  I will replace the old rubber fuel lines too – they aren’t fond of ethanol and should be replaced, anyway.  Danny plans to have my engine ready for me to pick up May 4.  Two weeks after that I’m hoping to be involved in install weekend.  Roughly three weeks thereafter I depart for Charlotte.  I cannot claim to be Charles Lindbergh, nor do I have a clue as to his Atlantic crossing pre-flight anxiety.  I do, however have a case of the nerves…  I like the challenge and the accompanying sense of urgency.  Here is the abyss I face:

RALPH-ROUTE

Round trip – Approximately 4,000 miles… Click to enjoy at a larger size!

I have a bunch of boxes filled with parts for the build…  They all arrived within the past couple weeks.  These goodies will go on the engine once it is hoisted and set into place.  Headers (first set arrived damaged, new ones already here), starter, dipsticks, fan, fan clutch, distributor, fuel pump, and a beautiful, 780 cfm QuickFuel carburetor:

Thanks to all the dinosaurs... Your sacrifice enables me to enjoy this piece of engineering...

Thanks to all the dinosaurs… Your sacrifice enables me to enjoy this piece of engineering…

More stuff to come.  Fuel lines, exhaust, radiator, and other items I’ll discover are critical to the project.  Forty five days remain…  More to do.  ‘nuf said.




Previous Article
Post # 8 - Pieces, Parts, and Stuff... Chipping Away at Various Chores.
Next Article
Great Googily Moogily!





2 Comments
Jim
onApril 24, 2014

Reply


Fantastico! How exciting. I think you’re making some smart decisions, dialing back the scope of the project to ensure completion in time for The Big Event. But boy, those front discs would be pretty nice to have, and shouldn’t be too bad a swap?

Onward!

    admin
    Ralph Trimmer
    onApril 30, 2014

    Reply


    Jim… Indeed! That’s the aim. As for the front discs… A rather painless swap… gonna be a matter of available time and money… we’ll see. Stay tuned, bruthuh!



Leave a Reply to admin Cancel reply

Your email address will not be published. Required fields are marked *



  • Recent Posts

    • Cold Air Induction Project II: The Quickening May 16, 2016
    • The Duster Gets a Homemade Cold Air Induction Setup! May 2, 2016
    • Looking Back: A Hot Rod Power Tour Retrospective January 21, 2016
    • Post #12 – Work Continues… January 8, 2015
    • Post #11 – 2014 Power Tour… I Don’t Think So. January 7, 2015
  • Categories

    • 1963 Impala
    • 1966 Charger
    • 1968 Camaro SS
    • 1969 GTO Judge
    • 1969 Torino GT
    • 1972 Cutlass
    • 1972 Hemi Duster
    • Hot Rod Power Tour
    • Power Tour 2012
    • Power Tour 2013
    • Power Tour 2014
    • Power Tour 2015
    • Power Tour Live Blog
    • Power Tour Live Blog 2014
    • PROJECT BEDLAM
    • Project Cars
    • Random Torino Information
    • Slide Show
    • Torino Parts
    • Uncategorized
  • Recent Comments

    • John on Mr. Black and The Lincoln Reach an Important Milestone
    • Mr. Trimmer's student with the cowboy hat. on Post #10 – The Engine – SARVIS Prepared
    • REJEAN LACHANCE on Using a B&M Cable Shifter with a Ford FMX Transmission
    • Juri on 1969 Torino, Part 2, (August, 2004)
    • JHCain on Using a B&M Cable Shifter with a Ford FMX Transmission
  • Discussion Forum Login

    Log In
    Register Lost Password



Copyright 2014 Amalgamated Rod & Speed.
Back to top